Zvizzer
ZV005TMY-1
THERMO MINI Soft Cut Foam Pad
Mini finishing pad from the German brand ZviZZer, to correct the finest defects and holograms, achieving a perfect finish.
- Available sizes: 15/25mm.
- Thermo Foam.
- Very resistant hook-and-loop
- For use with a Dremel or Autotriz Nano Polisher system.
€1.43
(€1.43 L'unité)
In stock
- shipped within 24h/72h
Pay in 3 installments with
from €100 of purchase.
By purchasing this product you can earn up to 1 points loyalty.
Your cart total will be
1 points equivalent to a discount voucher of €0.20
from €100 of purchase.
Description
The THERMO MINI Soft Cut Foam Pad Yellow is a mini pad of exceptional manufacture, dedicated to finishing work. ZviZZer needs no introduction when it comes to the quality and durability of their polishing foams. A current worldwide reference.
The build quality is evident in the strength of the hook-and-loop on one hand, with a very strong adhesive between the foam and the hook-and-loop. The honeycomb and aerated foam structure (known as open-cell) also ensures perfect heat distribution.
This mini pad is designed for use with a micro-machine such as a Dremel with a mini backing plate or the Autotriz Nano Polisher 3.0.
Once equipped with this THERMO MINI Soft Cut Foam Pad, your tool will allow you to reach the most difficult areas such as logo interiors, lettering, wheel spokes, etc.
The Thermo foam used in this mini pad is very special and allows it to resist deformation under pressure, while preventing the pad from softening and completely losing performance. This Thermo foam, which equips all ZviZZer foam pads, delivers considerably greater performance and pad durability (up to 3 to 4 times longer than a similar pad in traditional foam).
ZviZZer uses a registered and protected color code system specific to their pad range, to perfectly identify which polish should be used with which pad and also potentially with which drying microfiber. Thus, this THERMO MINI Soft Cut Foam Pad Yellow can be used with ZviZZer Fine Cut Hologram Remover (FC2000) polish or any other finishing polish from another brand.
The fineness of the foam on this finishing pad will ensure a perfect finish even on the most delicate and difficult paint shades (high gloss direct, solid finish, etc.). Ideal for finishing work after a pass with a coarser pad.
A pad of exceptional quality, with excellent hook-and-loop durability, ensuring a perfect finish in all circumstances.
Available in sizes:
- 15mm (thickness: 10mm)
- 25mm (thickness: 10mm)
Available individually or in packs.
Main specifications of the THERMO MINI Soft Cut Foam Pad:
- Abrasiveness: Fine.
- Thermo Foam
- Color: Yellow
- Thickness: 10mm
- Very resistant hook-and-loop.
Learn more about Zvizzer
** Zvizzer - German Innovation at the Service of Automotive Polishing **
ZviZZer is a German brand specializing in automotive polishing, recognized for its expertise and innovation. It offers a complete range of foam, wool, and microfiber pads, as well as next-generation water-based polishes, guaranteeing dust-free and odor-free use. Zvizzer brings disruptive innovation to Detailing: THERMO foams, which do not deform with heat during polishing, allowing you to work your polish much longer without damaging your pad.
To be used with
Instructions for use
How to use the THERMO MINI Soft Cut Foam Pad?
- Ensure you select the correct mini pad size for your backing plate (e.g. a 25mm size from ZviZZer will suit a 25mm or smaller backing plate).
- Center your mini pad on your backing plate.
- Apply a small pea-sized drop of polish (e.g. Fine Cut FC 2000) directly onto the pad.
- Spread your polish quickly at low speed over a small section.
- Then work your polish at low speed (900 RPM). Take care not to apply excessive pressure on sharp edges and body lines.
- Complete your pass when the residual polish film becomes very thin, near translucent.
- Buff off your polish with a suitable microfiber towel (e.g. Microfibre Cloth Jaune) after using a pad with Clean Top (alcohol-based panel wipe)
- Inspect your finish, then apply a protective wax or sealant.
Tip: Regularly clean your pad with ZviZZer Pad Cleaner to keep your foam completely free of spent polish and dust. Your workflow and results will be significantly improved. Spray Pad Cleaner directly onto the pad, massage the foam between your fingers, and then wipe clean with a microfiber towel or run the pad through a Pad Washer.
Specifications
BUILD QUALITY
One of the finest pad finishes currently on the market. Highly durable hook-and-loop backing.
THERMO FOAM
Specialized foam resistant to deformation and temperature build-up.
ACCESSIBILITY
This mini pad provides full access to tight, intricate areas.
AVAILABLE IN MULTIPLE SIZES AND PACKS
Available in 2 sizes and value packs.
Care instructions
- Always clean your pad regularly with Pad Cleaner
- Never leave an object or tool resting on top of the pad.
- Never wash a polishing pad in a washing machine.
- Always pull gently on the hook-and-loop backing to remove the pad from the backing plate.
Product sheet
Color
Yellow
PAD material
Foam
PAD Technology
Thermo
Foam density COLD (kPa)
10
HOT foam density (kPa)
9
Cells (1-cm-line)
24/26
Use with Dremel
Yes
Use with the Autotriz Nano Polisher
Yes
Our customers' reviews of this product
Frequently questions
FAQ
Be the first to ask a question about this product!
Question about the product
You may also like
Recently viewed products